STAVELEIGH, WAKEFIELD ROAD

Your options for this home

Using the recorded floor area and EPC characteristics, this 1276m² pre-1900 detached home has a current EPC rating of F35 and mains-gas heating. HotAndCold estimates a space-heating requirement of approximately 148.0–189.0kW. This property's recorded energy efficiency is comparatively low. The estimated heat demand per square metre is towards the higher end.

Hot&Cold snapshot

What stands out about this home

How this home compares locally

Based on 17 EPC-recorded properties nearby.

Built form

Detached

Internal area (EPC)

1276 m²

Building footprint

~344 m²

Approx. dimensions

~26.2 × 15.1 m

Main building axis

N–S

Estimated floors

2

Nearest building

0.5 m

Footprint & dimensions derived from Overture Maps building data (ODbL). Approximate, not survey-grade.

How this home is constructed & heated

Recorded on its Energy Performance Certificate.

Walls

Solid brick, as built, no insulation (assumed)

Roof

Pitched, no insulation (assumed)

Windows

Some double glazing

Main heating

Boiler and radiators, mains gas, Boiler and radiators, mains gas

Heating controls

Programmer, TRVs and bypass

Hot water

From main system, no cylinder thermostat

Floor

Solid, no insulation (assumed)

Energy improvement potential

Recommended improvements for this property

Measures from this home’s official Energy Performance Certificate assessment that could raise its rating and cut running costs, specific to STAVELEIGH, WAKEFIELD ROAD, STALYBRIDGE, SK15 3BY.

1. 1
   Draught proof single-glazed windowsIndicative cost: £80 - £120

   Fitting draught proofing, strips of insulation around windows and doors, will improve the comfort in the home. A contractor can be employed but draught proofing can be installed by a competent DIY enthusiast.

2. 2
   Room-in-roof insulationIndicative cost: £1,500 - £2,700

   Insulating roof rooms will significantly reduce heat loss; this will improve levels of comfort, reduce energy use and lower fuel bills. If it has a flat ceiling insulation can usually be added above the ceiling, and sloping ceilings and walls of roof rooms can be insulated using an internal lining board. Further information about roof room insulation and details of local contractors can be obtained from the National Insulation Association (www.nationalinsulationassociation.org.uk).

3. 3
   Replace boiler with new condensing boilerIndicative cost: £2,200 - £3,000

   A condensing boiler is capable of much higher efficiencies than other types of boiler, meaning it will burn less fuel to heat this property. This improvement is most appropriate when the existing central heating boiler needs repair or replacement, but there may be exceptional circumstances making this impractical. Condensing boilers need a drain for the condensate which limits their location; remember this when considering remodelling the room containing the existing boiler even if the latter is to be retained for the time being (for example a kitchen makeover). It is best to obtain advice from a qualified heating engineer. Ask the engineer to explain the options.

4. 4
   Solar photovoltaic panels, 2.5 kWpIndicative cost: £3,500 - £5,500

   A solar PV system is one which converts light directly into electricity via panels placed on the roof with no waste and no emissions. This electricity is used throughout the home in the same way as the electricity purchased from an energy supplier. The British Photovoltaic Association has up-to-date information on local installers who are qualified electricians. It is best to obtain advice from a qualified electrician. Ask the electrician to explain the options.

5. 5
   50 mm internal or external wall insulationIndicative cost: £4,000 - £14,000

   Solid wall insulation involves adding a layer of insulation to either the inside or the outside surface of the external walls, which reduces heat loss and lowers fuel bills. As it is more expensive than cavity wall insulation it is only recommended for walls without a cavity, or where for technical reasons a cavity cannot be filled. Internal insulation, known as dry-lining, is where a layer of insulation is fixed to the inside surface of external walls; this type of insulation is best applied when rooms require redecorating and can be installed by a competent DIY enthusiast. External solid wall insulation is the application of an insulant and a weather-protective finish to the outside of the wall. This may improve the look of the home, particularly where existing brickwork or rendering is poor, and will provide long-lasting weather protection. Further information can be obtained from the National Insulation Association (www.nationalinsulationassociation.org.uk).

6. 6
   Replace single glazed windows with low-E double glazed windowsIndicative cost: £3,300 - £6,500

   Double glazing is the term given to a system where two panes of glass are made up into a sealed unit. Replacing existing single-glazed windows with double-glazed windows will improve comfort in the home by reducing draughts and cold spots near windows. Double-glazed windows may also reduce noise, improve security and combat problems with condensation.

7. 7
   Floor insulation (solid floor)Indicative cost: £4,000 - £6,000

   Insulation of a floor will significantly reduce heat loss; this will improve levels of comfort, reduce energy use and lower fuel bills. Further information about floor insulation is available from many sources including www.energysavingtrust.org.uk/northernireland/Insulation/Floor-insulation.

Source: the property’s domestic EPC recommendations (open data). Indicative only, get a professional survey before committing to any measure.

Energy rating history

Recorded change: -38 EPC points across 2 certificates.

1. 2016C73
2. 2024F35

Other homes nearby