ROESIDE FARM, BRADSHAW LANE

Your options for this home

Based on this property's recorded characteristics, this 166m² pre-1900 detached home has a current EPC rating of E42 and mains-gas heating. HotAndCold estimates a space-heating requirement of approximately 19.0–24.5kW. Its current energy rating indicates relatively weak energy performance compared with more efficient homes. Its modelled space-heating intensity per square metre is relatively high.

Hot&Cold snapshot

What stands out about this home

How this home compares locally

Based on 7 EPC-recorded properties nearby.

Built form

Detached

Internal area (EPC)

166 m²

Building footprint

~224 m²

Approx. dimensions

~26.1 × 16.2 m

Main building axis

N–S

Estimated floors

2

Nearest building

4.1 m

Footprint & dimensions derived from Overture Maps building data (ODbL). Approximate, not survey-grade.

How this home is constructed & heated

Recorded on its Energy Performance Certificate.

Walls

Granite or whinstone, as built, no insulation (assumed)

Roof

Pitched, no insulation (assumed)

Windows

Some double glazing

Main heating

Boiler and radiators, mains gas

Heating controls

Room thermostat only

Hot water

From main system

Floor

Solid, no insulation (assumed)

Energy improvement potential

Recommended improvements for this property

Measures from this home’s official Energy Performance Certificate assessment that could raise its rating and cut running costs, specific to ROESIDE FARM, BRADSHAW LANE, CHAPEL-EN-LE-FRITH, HIGH PEAK, SK23 9UL.

1. 1
   Upgrade heating controlsIndicative cost: £350 - £450

   The heating system would benefit from a programmer to provide better comfort through automatic control of the system. A modern programmer can provide different time programmes for heating and hot water, allowing different time periods to be set for each; seven-day programmers also allow different heating and/or hot water patterns to be set for weekdays and weekends and holidays. Thermostatic radiator valves should also be installed, to allow the temperature of each room to be controlled to suit individual needs, adding to comfort and reducing heating bills provided internal doors are kept closed. For example, they can be set to be warmer in the living room and bathroom than in the bedrooms. Ask a competent heating engineer to install thermostatic radiator valves and a fully pumped system with the pump and the boiler turned off by the room thermostat. Thermostatic radiator valves should be fitted to every radiator except for the radiator in the same room as the room thermostat. Remember the room thermostat is needed as well as the thermostatic radiator valves, to enable the boiler to switch off when no heat is required. It is best to obtain advice from a qualified heating engineer.

2. 2
   Flat roof or sloping ceiling insulationIndicative cost: £850 - £1,500

   Insulation of a flat roof or sloping ceiling will significantly reduce heat loss through the roof; this will improve levels of comfort, reduce energy use and lower fuel bills. Where the weatherproof membrane is sound and the roof construction is appropriate, suitable insulation can be placed on top of the roof membrane (inverted roof). Alternatively, where the weatherproof membrane needs to be replaced insulation can be provided under the weatherproof membrane (warm roof). Further information about roof insulation and details of local contractors can be obtained from the National Insulation Association (www.nationalinsulationassociation.org.uk).

3. 3
   Floor insulation (solid floor)Indicative cost: £4,000 - £6,000

   Insulation of a floor will significantly reduce heat loss; this will improve levels of comfort, reduce energy use and lower fuel bills. Further information about floor insulation is available from many sources including www.energysavingtrust.org.uk/northernireland/Insulation/Floor-insulation.

4. 4
   Replace single glazed windows with low-E double glazed windowsIndicative cost: £3,300 - £6,500

   Double glazing is the term given to a system where two panes of glass are made up into a sealed unit. Replacing existing single-glazed windows with double-glazed windows will improve comfort in the home by reducing draughts and cold spots near windows. Double-glazed windows may also reduce noise, improve security and combat problems with condensation.

5. 5
   50 mm internal or external wall insulationIndicative cost: £4,000 - £14,000

   Solid wall insulation involves adding a layer of insulation to either the inside or the outside surface of the external walls, which reduces heat loss and lowers fuel bills. As it is more expensive than cavity wall insulation it is only recommended for walls without a cavity, or where for technical reasons a cavity cannot be filled. Internal insulation, known as dry-lining, is where a layer of insulation is fixed to the inside surface of external walls; this type of insulation is best applied when rooms require redecorating and can be installed by a competent DIY enthusiast. External solid wall insulation is the application of an insulant and a weather-protective finish to the outside of the wall. This may improve the look of the home, particularly where existing brickwork or rendering is poor, and will provide long-lasting weather protection. Further information can be obtained from the National Insulation Association (www.nationalinsulationassociation.org.uk).

6. 6
   Draught proof single-glazed windowsIndicative cost: £80 - £120

   Fitting draught proofing, strips of insulation around windows and doors, will improve the comfort in the home. A contractor can be employed but draught proofing can be installed by a competent DIY enthusiast.

7. 7
   Solar water heatingIndicative cost: £4,000 - £6,000

   A solar water heating panel, usually fixed to the roof, uses the sun to pre-heat the hot water supply. This will significantly reduce the demand on the heating system to provide hot water and hence save fuel and money. The Solar Trade Association has up-to-date information on local installers.

8. 8
   Wind turbineIndicative cost: £15,000 - £25,000

   A wind turbine provides electricity from wind energy. This electricity is used throughout the home in the same way as the electricity purchased from an energy supplier. The British Wind Energy Association has up-to-date information on suppliers of small-scale wind systems. Wind turbines are not suitable for all properties. The system’s effectiveness depends on local wind speeds and the presence of nearby obstructions, and a site survey should be undertaken by an accredited installer.

9. 9
   Solar photovoltaic panels, 2.5 kWpIndicative cost: £3,500 - £5,500

   A solar PV system is one which converts light directly into electricity via panels placed on the roof with no waste and no emissions. This electricity is used throughout the home in the same way as the electricity purchased from an energy supplier. The British Photovoltaic Association has up-to-date information on local installers who are qualified electricians. It is best to obtain advice from a qualified electrician. Ask the electrician to explain the options.

Source: the property’s domestic EPC recommendations (open data). Indicative only, get a professional survey before committing to any measure.

Other homes nearby