PYATTS BARN FARM, DINGLE LANE

Your options for this home

From the available property and energy data, this 234m² pre-1900 detached home has a current EPC rating of D63 and its recorded heating. HotAndCold estimates a space-heating requirement of approximately 22.5–29.0kW. The recorded EPC score places this home in the middle of the efficiency range. Its modelled space-heating intensity per square metre is relatively high.

Hot&Cold snapshot

What stands out about this home

How this home compares locally

Based on 9 EPC-recorded properties nearby.

Built form

Detached

Internal area (EPC)

234 m²

Building footprint

~139 m²

Approx. dimensions

~20.1 × 8.8 m

Main building axis

N–S

Estimated floors

1

Nearest building

3.5 m

Footprint & dimensions derived from Overture Maps building data (ODbL). Approximate, not survey-grade.

How this home is constructed & heated

Recorded on its Energy Performance Certificate.

Walls

Granite or whinstone, with internal insulation

Roof

Pitched, 150 mm loft insulation

Windows

Fully double glazed

Main heating

Boiler and radiators, LPG

Heating controls

Programmer and room thermostat

Hot water

From main system, no cylinder thermostat

Floor

Solid, no insulation (assumed)

Energy improvement potential

Recommended improvements for this property

Measures from this home’s official Energy Performance Certificate assessment that could raise its rating and cut running costs, specific to PYATTS BARN FARM, DINGLE LANE, RUSHTON SPENCER, MACCLESFIELD, SK11 0RU.

1. 1
   Increase loft insulation to 270 mmIndicative cost: $100 - $350

   Loft insulation laid in the loft space or between roof rafters to a depth of at least 270 mm will significantly reduce heat loss through the roof; this will improve levels of comfort, reduce energy use and lower fuel bills. Insulation should not be placed below any cold water storage tank; any such tank should also be insulated on its sides and top, and there should be boarding on battens over the insulation to provide safe access between the loft hatch and the cold water tank. The insulation can be installed by professional contractors but also by a capable DIY enthusiast. Loose granules may be used instead of insulation quilt; this form of loft insulation can be blown into place and can be useful where access is difficult. The loft space must have adequate ventilation to prevent dampness; seek advice about this if unsure (particularly if installing insulation between rafters because a vapour control layer and ventilation above the insulation are required). Further information about loft insulation and details of local contractors can be obtained from the National Insulation Association (www.nationalinsulationassociation.org.uk).

2. 2
   Floor insulation (solid floor)Indicative cost: $4,000 - $6,000

   Insulation of a floor will significantly reduce heat loss; this will improve levels of comfort, reduce energy use and lower fuel bills. Further information about floor insulation is available from many sources including www.energysavingtrust.org.uk/northernireland/Insulation/Floor-insulation.

3. 3
   Hot water cylinder thermostatIndicative cost: $200 - $400

   A hot water cylinder thermostat enables the boiler to switch off when the water in the cylinder reaches the required temperature; this minimises the amount of energy that is used and lowers fuel bills. The thermostat is a temperature sensor that sends a signal to the boiler when the required temperature is reached. To be fully effective it needs to be sited in the correct position and hard wired in place, so it should be installed by a competent plumber or heating engineer.

4. 4
   Upgrade heating controlsIndicative cost: $350 - $450

   Thermostatic radiator valves allow the temperature of each room to be controlled to suit individual needs, adding to comfort and reducing heating bills provided internal doors are kept closed. For example, they can be set to be warmer in the living room and bathroom than in the bedrooms. Ask a competent heating engineer to install thermostatic radiator valves. Thermostatic radiator valves should be fitted to every radiator except the radiator in the same room as the room thermostat. Remember the room thermostat is needed as well as the thermostatic radiator valves, to enable the boiler to switch off when no heat is required. It is best to obtain advice from a qualified heating engineer.

5. 5
   Wind turbineIndicative cost: $15,000 - $25,000

   A wind turbine provides electricity from wind energy. This electricity is used throughout the home in the same way as the electricity purchased from an energy supplier. The British Wind Energy Association has up-to-date information on suppliers of small-scale wind systems. Wind turbines are not suitable for all properties. The system’s effectiveness depends on local wind speeds and the presence of nearby obstructions, and a site survey should be undertaken by an accredited installer.

6. 6
   Solar water heatingIndicative cost: $4,000 - $6,000

   A solar water heating panel, usually fixed to the roof, uses the sun to pre-heat the hot water supply. This will significantly reduce the demand on the heating system to provide hot water and hence save fuel and money. The Solar Trade Association has up-to-date information on local installers.

Source: the property’s domestic EPC recommendations (open data). Indicative only, get a professional survey before committing to any measure.

Other homes nearby