FOUNDRY COTTAGE, HYDE BANK ROAD

Your options for this home

From the available property and energy data, this 149m² 2000s detached home has a current EPC rating of D59 and its recorded heating. HotAndCold estimates a space-heating requirement of approximately 6.5–9.0kW. Its current energy rating indicates moderate energy efficiency. Its modelled space-heating intensity per square metre is relatively low.

Hot&Cold snapshot

What stands out about this home

How this home compares locally

Based on 25827 EPC-recorded properties nearby.

Built form

Detached

Internal area (EPC)

149 m²

Building footprint

~95 m²

Approx. dimensions

~10.8 × 10.3 m

Main building axis

N–S

Estimated floors

2

Nearest building

31.2 m

Footprint & dimensions derived from Overture Maps building data (ODbL). Approximate, not survey-grade.

How this home is constructed & heated

Recorded on its Energy Performance Certificate.

Walls

Sandstone or limestone, as built, insulated (assumed)

Roof

Pitched, insulated (assumed)

Windows

Fully double glazed

Main heating

Boiler and radiators, dual fuel (mineral and wood)

Heating controls

No time or thermostatic control of room temperature

Hot water

From main system, no cylinder thermostat

Floor

Solid, insulated (assumed)

Energy improvement potential

Recommended improvements for this property

Measures from this home’s official Energy Performance Certificate assessment that could raise its rating and cut running costs, specific to FOUNDRY COTTAGE, HYDE BANK ROAD, NEW MILLS, HIGH PEAK, SK22 4BP.

1. 1
   Upgrade heating controlsIndicative cost: £350 - £450

   The heating system would benefit from a programmer and room thermostat to enable the boiler to switch off when no heat is required; this will reduce the amount of energy used and lower fuel bills. Thermostatic radiator valves should also be installed, to allow the temperature of each room to be controlled to suit individual needs, adding to comfort and reducing heating bills. For example, they can be set to be warmer in the living room and bathroom than in the bedrooms. Ask a competent heating engineer to install thermostatic radiator valves and a fully pumped system with the pump and the boiler turned off by the room thermostat. Thermostatic radiator valves should be fitted to every radiator except one – the radiator in the same room as the room thermostat. Remember the room thermostat is needed as well as the thermostatic radiator valves, to enable the boiler to switch off when no heat is required. It is best to obtain advice from a qualified heating engineer.

2. 2
   Low energy lighting for all fixed outletsIndicative cost: £40

   Replacement of traditional light bulbs with energy saving recommended ones will reduce lighting costs over the lifetime of the bulb, and they last up to 12 times longer than ordinary light bulbs. Also consider selecting low energy light fittings when redecorating; contact the Lighting Association for your nearest stockist of Domestic Energy Efficient Lighting Scheme fittings.

3. 3
   Draught proof single-glazed windowsIndicative cost: £80 - £120

   Fitting draught proofing, strips of insulation around windows and doors, will improve the comfort in the home. A contractor can be employed but draught proofing can be installed by a competent DIY enthusiast.

4. 4
   Solar water heatingIndicative cost: £4,000 - £6,000

   A solar water heating panel, usually fixed to the roof, uses the sun to pre-heat the hot water supply. This will significantly reduce the demand on the heating system to provide hot water and hence save fuel and money. The Solar Trade Association has up-to-date information on local installers.

5. 5
   Solar photovoltaic panels, 2.5 kWpIndicative cost: £3,500 - £5,500

   A solar PV system is one which converts light directly into electricity via panels placed on the roof with no waste and no emissions. This electricity is used throughout the home in the same way as the electricity purchased from an energy supplier. The British Photovoltaic Association has up-to-date information on local installers who are qualified electricians. It is best to obtain advice from a qualified electrician. Ask the electrician to explain the options.

6. 6
   Increase hot water cylinder insulationIndicative cost: £15 - £30

   Increasing the thickness of existing insulation around the hot water cylinder will help to maintain the water at the required temperature; this will reduce the amount of energy used and lower fuel bills. An additional cylinder jacket or other suitable insulation layer can be used. The insulation should be fitted over any thermostat clamped to the cylinder. Hot water pipes from the hot water cylinder should also be insulated, using pre-formed pipe insulation of up to 50 mm thickness (or to suit the space available) for as far as they can be accessed to reduce losses in summer. All these materials can be purchased from DIY stores and installed by a competent DIY enthusiast.

Source: the property’s domestic EPC recommendations (open data). Indicative only, get a professional survey before committing to any measure.

Other homes nearby