FLAT 10, 406 MOSS LANE EAST

Your options for this home

Based on this property's recorded characteristics, this 34m² flat has a current EPC rating of D60 and mains-gas heating. HotAndCold estimates a space-heating requirement of approximately 3.0–4.0kW. The recorded EPC score places this home in the middle of the efficiency range. The estimated heat demand per square metre is around typical levels.

Hot&Cold snapshot

What stands out about this home

How this home compares locally

Based on 23 EPC-recorded properties nearby.

Built form

Flat

Internal area (EPC)

34 m²

Building footprint

~219 m²

Approx. dimensions

~18.2 × 13.4 m

Main building axis

N–S

Estimated floors

3

Nearest building

7.0 m

Footprint & dimensions derived from Overture Maps building data (ODbL). Approximate, not survey-grade.

How this home is constructed & heated

Recorded on its Energy Performance Certificate.

Walls

Solid brick, as built, no insulation (assumed)

Roof

(another dwelling above)

Windows

Single glazed

Main heating

Boiler and radiators, mains gas

Heating controls

Programmer, room thermostat and TRVs

Hot water

From main system

Floor

(another dwelling below)

Energy improvement potential

Recommended improvements for this property

Measures from this home’s official Energy Performance Certificate assessment that could raise its rating and cut running costs, specific to FLAT 10, 406 MOSS LANE EAST, MANCHESTER, M14 4PX.

1. 1
   Replace single glazed windows with low-E double glazed windowsIndicative cost: £3,300 - £6,500

   Double glazing is the term given to a system where two panes of glass are made up into a sealed unit. Replacing existing single-glazed windows with double-glazed windows will improve comfort in the home by reducing draughts and cold spots near windows. Double-glazed windows may also reduce noise, improve security and combat problems with condensation.

2. 2
   Low energy lighting for all fixed outletsIndicative cost: £5

   Replacement of traditional light bulbs with energy saving recommended ones will reduce lighting costs over the lifetime of the bulb, and they last up to 12 times longer than ordinary light bulbs. Also consider selecting low energy light fittings when redecorating; contact the Lighting Association for your nearest stockist of Domestic Energy Efficient Lighting Scheme fittings.

3. 3
   Replace boiler with new condensing boilerIndicative cost: £2,200 - £3,000

   A condensing boiler is capable of much higher efficiencies than other types of boiler, meaning it will burn less fuel to heat this property. This improvement is most appropriate when the existing central heating boiler needs repair or replacement, but there may be exceptional circumstances making this impractical. Condensing boilers need a drain for the condensate which limits their location; remember this when considering remodelling the room containing the existing boiler even if the latter is to be retained for the time being (for example a kitchen makeover). It is best to obtain advice from a qualified heating engineer. Ask the engineer to explain the options.

4. 4
   50 mm internal or external wall insulationIndicative cost: £4,000 - £14,000

   Solid wall insulation involves adding a layer of insulation to either the inside or the outside surface of the external walls, which reduces heat loss and lowers fuel bills. As it is more expensive than cavity wall insulation it is only recommended for walls without a cavity, or where for technical reasons a cavity cannot be filled. Internal insulation, known as dry-lining, is where a layer of insulation is fixed to the inside surface of external walls; this type of insulation is best applied when rooms require redecorating and can be installed by a competent DIY enthusiast. External solid wall insulation is the application of an insulant and a weather-protective finish to the outside of the wall. This may improve the look of the home, particularly where existing brickwork or rendering is poor, and will provide long-lasting weather protection. Further information can be obtained from the National Insulation Association (www.nationalinsulationassociation.org.uk).

5. 5
   Draught proof single-glazed windowsIndicative cost: £80 - £120

   Fitting draught proofing, strips of insulation around windows and doors, will improve the comfort in the home. A contractor can be employed but draught proofing can be installed by a competent DIY enthusiast.

Source: the property’s domestic EPC recommendations (open data). Indicative only, get a professional survey before committing to any measure.

Other homes nearby