7 LEYBOURNE AVENUE, MANCHESTER

Your options for this home

From the available property and energy data, this 73m² mid-terrace home has a current EPC rating of D58 and its recorded heating. HotAndCold estimates a space-heating requirement of approximately 5.0–6.5kW. Its current energy rating indicates moderate energy efficiency. Its modelled space-heating intensity per square metre is moderate.

Hot&Cold snapshot

What stands out about this home

How this home compares locally

Based on 15 EPC-recorded properties nearby.

Built form

Mid-terrace

Internal area (EPC)

73 m²

Building footprint

~56 m²

Approx. dimensions

~11.2 × 5.7 m

Main building axis

E–W

Nearest building

0.0 m

Footprint & dimensions derived from Overture Maps building data (ODbL). Approximate, not survey-grade.

How this home is constructed & heated

Recorded on its Energy Performance Certificate.

Walls

Solid brick, with internal insulation

Roof

Pitched, 300 mm loft insulation

Windows

Fully double glazed

Main heating

Electric storage heaters

Heating controls

Controls for high heat retention storage heaters

Hot water

Electric immersion, off-peak

Floor

Solid, no insulation (assumed)

Energy improvement potential

Recommended improvements for this property

Measures from this home’s official Energy Performance Certificate assessment that could raise its rating and cut running costs, specific to 7 LEYBOURNE AVENUE, MANCHESTER, M19 3FG.

1. 1
   Solar photovoltaic panels, 2.5 kWpIndicative cost: £3,500 - £5,500

   A solar PV system is one which converts light directly into electricity via panels placed on the roof with no waste and no emissions. This electricity is used throughout the home in the same way as the electricity purchased from an energy supplier. The British Photovoltaic Association has up-to-date information on local installers who are qualified electricians. It is best to obtain advice from a qualified electrician. Ask the electrician to explain the options.

2. 2
   Draught proof single-glazed windowsIndicative cost: £80 - £120

   Fitting draught proofing, strips of insulation around windows and doors, will improve the comfort in the home. A contractor can be employed but draught proofing can be installed by a competent DIY enthusiast.

3. 3
   Solar water heatingIndicative cost: £4,000 - £6,000

   A solar water heating panel, usually fixed to the roof, uses the sun to pre-heat the hot water supply. This will significantly reduce the demand on the heating system to provide hot water and hence save fuel and money. The Solar Trade Association has up-to-date information on local installers.

4. 4
   Floor insulation (solid floor)Indicative cost: £4,000 - £6,000

   Insulation of a floor will significantly reduce heat loss; this will improve levels of comfort, reduce energy use and lower fuel bills. Further information about floor insulation is available from many sources including www.energysavingtrust.org.uk/northernireland/Insulation/Floor-insulation.

5. 5
   High heat retention storage heaters and dual immersion cylinderIndicative cost: £1,600 - £2,400

   Modern storage heaters have better insulation and are easier to control than the older type in the property. Ask for a quotation for new, high heat retention heaters with automatic charge and output controls. A dual-immersion cylinder, which can be installed at the same time, will provide cheaper hot water than the system currently installed. As installations should be in accordance with the current regulations covering electrical wiring, only a qualified electrician should carry out the installation. It is best to obtain advice from a qualified heating engineer. Ask the engineer to explain

6. 6
   Increase hot water cylinder insulationIndicative cost: £15 - £30

   Increasing the thickness of existing insulation around the hot water cylinder will help to maintain the water at the required temperature; this will reduce the amount of energy used and lower fuel bills. An additional cylinder jacket or other suitable insulation layer can be used. The insulation should be fitted over any thermostat clamped to the cylinder. Hot water pipes from the hot water cylinder should also be insulated, using pre-formed pipe insulation of up to 50 mm thickness (or to suit the space available) for as far as they can be accessed to reduce losses in summer. All these materials can be purchased from DIY stores and installed by a competent DIY enthusiast.

Source: the property’s domestic EPC recommendations (open data). Indicative only, get a professional survey before committing to any measure.

Energy rating history

Recorded change: +6 EPC points across 3 certificates.

1. 2015E52
2. 2017F33
3. 2024D58

Other homes nearby