56 STATION ROAD, BLACKROD

Your options for this home

From the available property and energy data, this 110m² 1930s detached home has a current EPC rating of G13 and its recorded heating. HotAndCold estimates a space-heating requirement of approximately 9.0–11.5kW. This property's recorded energy efficiency is comparatively low. The estimated heat demand per square metre is around typical levels.

Hot&Cold snapshot

What stands out about this home

How this home compares locally

Based on 10 EPC-recorded properties nearby.

Built form

Detached

Internal area (EPC)

110 m²

Building footprint

~81 m²

Approx. dimensions

~11.8 × 8.6 m

Main building axis

NW–SE

Nearest building

1.1 m

Footprint & dimensions derived from Overture Maps building data (ODbL). Approximate, not survey-grade.

How this home is constructed & heated

Recorded on its Energy Performance Certificate.

Walls

Cavity wall, filled cavity

Roof

Pitched, no insulation

Windows

Fully double glazed

Main heating

No system present: electric heaters assumed

Heating controls

None

Hot water

Electric immersion, standard tariff

Floor

Suspended, no insulation (assumed)

Energy improvement potential

Recommended improvements for this property

Measures from this home’s official Energy Performance Certificate assessment that could raise its rating and cut running costs, specific to 56 STATION ROAD, BLACKROD, BOLTON, BL6 5BW.

1. 1
   Wind turbineIndicative cost: £1,500 - £4,000

   A wind turbine provides electricity from wind energy. This electricity is used throughout the home in the same way as the electricity purchased from an energy supplier. The British Wind Energy Association has up-to-date information on suppliers of small-scale wind systems. Wind turbines are not suitable for all properties. The system’s effectiveness depends on local wind speeds and the presence of nearby obstructions, and a site survey should be undertaken by an accredited installer.

2. 2
   Increase loft insulation to 270 mmIndicative cost: £100 - £350

   Loft insulation laid in the loft space or between roof rafters to a depth of at least 270 mm will significantly reduce heat loss through the roof; this will improve levels of comfort, reduce energy use and lower fuel bills. Insulation should not be placed below any cold water storage tank; any such tank should also be insulated on its sides and top, and there should be boarding on battens over the insulation to provide safe access between the loft hatch and the cold water tank. The insulation can be installed by professional contractors but also by a capable DIY enthusiast. Loose granules may be used instead of insulation quilt; this form of loft insulation can be blown into place and can be useful where access is difficult. The loft space must have adequate ventilation to prevent dampness; seek advice about this if unsure (particularly if installing insulation between rafters because a vapour control layer and ventilation above the insulation are required). Further information about loft insulation and details of local contractors can be obtained from the National Insulation Association (www.nationalinsulationassociation.org.uk).

3. 3
   Fan assisted storage heaters and dual immersion cylinderIndicative cost: £1500 - £2000

   Modern storage heaters are less expensive to run than the direct acting, on-peak heating system in the property. A dual-rate electricity supply is required to provide the off-peak electricity that these heaters use; this is easily obtained by contacting the energy supplier. Ask for a quotation for fan-assisted heaters with automatic charge control. A dual-immersion cylinder, which can be installed at the same time, will provide cheaper hot water than the system currently installed. As installations should be in accordance with the national wiring standards, only a qualified electrician should carry out the installation. Ask a qualified electrical heating engineer to explain the options, which might also include switching to other forms of electric heating.

4. 4
   Solar water heatingIndicative cost: £4,000 - £6,000

   A solar water heating panel, usually fixed to the roof, uses the sun to pre-heat the hot water supply. This will significantly reduce the demand on the heating system to provide hot water and hence save fuel and money. The Solar Trade Association has up-to-date information on local installers.

5. 5
   Floor insulationIndicative cost: £800 - £1,200

   Insulation of a floor will significantly reduce heat loss; this will improve levels of comfort, reduce energy use and lower fuel bills. Suspended floors can sometimes be insulated from below which means that the floor does not need to be lifted to install the insulation. Further information about floor insulation and details of local contractors can be obtained from the National Insulation Association (www.nationalinsulationassociation.org.uk).

6. 6
   Solar photovoltaic panels, 2.5 kWpIndicative cost: £9,000 - £14,000

   A solar PV system is one which converts light directly into electricity via panels placed on the roof with no waste and no emissions. This electricity is used throughout the home in the same way as the electricity purchased from an energy supplier. The British Photovoltaic Association has up-to-date information on local installers who are qualified electricians. It is best to obtain advice from a qualified electrician. Ask the electrician to explain the options.

7. 7
   Increase hot water cylinder insulationIndicative cost: £15 - £30

   Increasing the thickness of existing insulation around the hot water cylinder will help to maintain the water at the required temperature; this will reduce the amount of energy used and lower fuel bills. An additional cylinder jacket or other suitable insulation layer can be used. The insulation should be fitted over any thermostat clamped to the cylinder. Hot water pipes from the hot water cylinder should also be insulated, using pre-formed pipe insulation of up to 50 mm thickness (or to suit the space available) for as far as they can be accessed to reduce losses in summer. All these materials can be purchased from DIY stores and installed by a competent DIY enthusiast.

Source: the property’s domestic EPC recommendations (open data). Indicative only, get a professional survey before committing to any measure.

Energy rating history

Recorded change: -33 EPC points across 2 certificates.

1. 2014E46
2. 2014G13

Other homes nearby