56 ROCHDALE ROAD, SHAW

Your options for this home

HotAndCold's model combines the recorded floor area, property type and EPC data, so this 62m² pre-1900 mid-terrace home has a current EPC rating of F36 and mains-gas heating. HotAndCold estimates a space-heating requirement of approximately 5.5–7.0kW. Its current energy rating indicates relatively weak energy performance compared with more efficient homes. The estimated heat demand per square metre is around typical levels.

Hot&Cold snapshot

What stands out about this home

How this home compares locally

Based on 13 EPC-recorded properties nearby.

Sale history

Recorded sales for 56 ROCHDALE ROAD from HM Land Registry Price Paid data.

1. £124,995

   Mar 2020 · Terraced
2. £65,000

   Mar 2019 · Terraced
3. £50,000

   Apr 2008 · Terraced
4. £50,000

   Aug 2007 · Terraced

Contains HM Land Registry data © Crown copyright and database right. Sale prices are historic and not a current valuation.

Built form

Mid-terrace

Internal area (EPC)

62 m²

Building footprint

~41 m²

Approx. dimensions

~10.1 × 4.2 m

Main building axis

NE–SW

Nearest building

0.0 m

Footprint & dimensions derived from Overture Maps building data (ODbL). Approximate, not survey-grade.

How this home is constructed & heated

Recorded on its Energy Performance Certificate.

Walls

Sandstone, as built, no insulation (assumed)

Roof

Pitched, 12 mm loft insulation

Windows

Partial double glazing

Main heating

Room heaters, mains gas

Heating controls

No thermostatic control of room temperature

Hot water

Electric immersion, standard tariff

Floor

Solid, no insulation (assumed)

Energy improvement potential

Recommended improvements for this property

Measures from this home’s official Energy Performance Certificate assessment that could raise its rating and cut running costs, specific to 56 ROCHDALE ROAD, SHAW, OLDHAM, OL2 7SA.

1. 1
   Floor insulationIndicative cost: £800 - £1,200

   Insulation of a floor will significantly reduce heat loss; this will improve levels of comfort, reduce energy use and lower fuel bills. Suspended floors can sometimes be insulated from below which means that the floor does not need to be lifted to install the insulation. Further information about floor insulation and details of local contractors can be obtained from the National Insulation Association (www.nationalinsulationassociation.org.uk).

2. 2
   Replace single glazed windows with low-E double glazingIndicative cost: £3,300 - £6,500

   Double glazing is the term given to a system where two panes of glass are made up into a sealed unit. Replacing existing single-glazed windows with double glazing will improve comfort in the home by reducing draughts and cold spots near windows. Double-glazed windows may also reduce noise, improve security and combat problems with condensation.

3. 3
   Change room heaters to condensing boilerIndicative cost: £3,000 - £7,000

   A full central heating system using a condensing boiler will provide space and water heating at greater efficiency than gas room heaters, meaning it will burn less fuel to heat this property, but there may be exceptional circumstances making this impractical. Condensing boilers need a drain for the condensate which limits their location. Remember this when considering remodelling the room containing the existing boiler even if the latter is to be retained for the time being (for example a kitchen makeover). It is best to obtain advice from a qualified heating engineer. Ask the engineer to explain the options.

4. 4
   Solar photovoltaic panels, 2.5 kWpIndicative cost: £9,000 - £14,000

   A solar PV system is one which converts light directly into electricity via panels placed on the roof with no waste and no emissions. This electricity is used throughout the home in the same way as the electricity purchased from an energy supplier. The British Photovoltaic Association has up-to-date information on local installers who are qualified electricians. It is best to obtain advice from a qualified electrician. Ask the electrician to explain the options.

5. 5
   Wind turbineIndicative cost: £1,500 - £4,000

   A wind turbine provides electricity from wind energy. This electricity is used throughout the home in the same way as the electricity purchased from an energy supplier. The British Wind Energy Association has up-to-date information on suppliers of small-scale wind systems. Wind turbines are not suitable for all properties. The system’s effectiveness depends on local wind speeds and the presence of nearby obstructions, and a site survey should be undertaken by an accredited installer.

6. 6
   Solar water heatingIndicative cost: £4,000 - £6,000

   A solar water heating panel, usually fixed to the roof, uses the sun to pre-heat the hot water supply. This will significantly reduce the demand on the heating system to provide hot water and hence save fuel and money. The Solar Trade Association has up-to-date information on local installers.

7. 7
   Draught proof single-glazed windowsIndicative cost: £80 - £120

   Fitting draught proofing, strips of insulation around windows and doors, will improve the comfort in the home. A contractor can be employed but draught proofing can be installed by a competent DIY enthusiast.

8. 8
   50 mm internal or external wall insulationIndicative cost: £4,000 - £14,000

   Solid wall insulation involves adding a layer of insulation to either the inside or the outside surface of the external walls, which reduces heat loss and lowers fuel bills. As it is more expensive than cavity wall insulation it is only recommended for walls without a cavity, or where for technical reasons a cavity cannot be filled. Internal insulation, known as dry-lining, is where a layer of insulation is fixed to the inside surface of external walls; this type of insulation is best applied when rooms require redecorating and can be installed by a competent DIY enthusiast. External solid wall insulation is the application of an insulant and a weather-protective finish to the outside of the wall. This may improve the look of the home, particularly where existing brickwork or rendering is poor, and will provide long-lasting weather protection. Further information can be obtained from the National Insulation Association (www.nationalinsulationassociation.org.uk).

9. 9
   Increase loft insulation to 270 mmIndicative cost: £100 - £350

   Loft insulation laid in the loft space or between roof rafters to a depth of at least 270 mm will significantly reduce heat loss through the roof; this will improve levels of comfort, reduce energy use and lower fuel bills. Insulation should not be placed below any cold water storage tank; any such tank should also be insulated on its sides and top, and there should be boarding on battens over the insulation to provide safe access between the loft hatch and the cold water tank. The insulation can be installed by professional contractors but also by a capable DIY enthusiast. Loose granules may be used instead of insulation quilt; this form of loft insulation can be blown into place and can be useful where access is difficult. The loft space must have adequate ventilation to prevent dampness; seek advice about this if unsure (particularly if installing insulation between rafters because a vapour control layer and ventilation above the insulation are required). Further information about loft insulation and details of local contractors can be obtained from the National Insulation Association (www.nationalinsulationassociation.org.uk).

10. 10
    Increase hot water cylinder insulationIndicative cost: £15 - £30

    Increasing the thickness of existing insulation around the hot water cylinder will help to maintain the water at the required temperature; this will reduce the amount of energy used and lower fuel bills. An additional cylinder jacket or other suitable insulation layer can be used. The insulation should be fitted over any thermostat clamped to the cylinder. Hot water pipes from the hot water cylinder should also be insulated, using pre-formed pipe insulation of up to 50 mm thickness (or to suit the space available) for as far as they can be accessed to reduce losses in summer. All these materials can be purchased from DIY stores and installed by a competent DIY enthusiast.

11. 11
    Low energy lighting for all fixed outletsIndicative cost: £30

    Replacement of traditional light bulbs with energy saving recommended ones will reduce lighting costs over the lifetime of the bulb, and they last up to 12 times longer than ordinary light bulbs. Also consider selecting low energy light fittings when redecorating; contact the Lighting Association for your nearest stockist of Domestic Energy Efficient Lighting Scheme fittings.

Source: the property’s domestic EPC recommendations (open data). Indicative only, get a professional survey before committing to any measure.

Other homes nearby