32, KENNERLEY COURT

Your options for this home

HotAndCold's model combines the recorded floor area, property type and EPC data, so this 62m² 1960s flat has a current EPC rating of C71 and mains-gas heating. HotAndCold estimates a space-heating requirement of approximately 4.5–6.0kW. The recorded EPC score is comparatively high for existing housing stock. The estimated heat demand per square metre is around typical levels.

Hot&Cold snapshot

What stands out about this home

How this home compares locally

Based on 29 EPC-recorded properties nearby.

Built form

Flat

Internal area (EPC)

62 m²

Building footprint

~549 m²

Approx. dimensions

~46.6 × 19.1 m

Main building axis

E–W

Estimated floors

1

Nearest building

8.3 m

Footprint & dimensions derived from Overture Maps building data (ODbL). Approximate, not survey-grade.

How this home is constructed & heated

Recorded on its Energy Performance Certificate.

Walls

Cavity wall, filled cavity

Roof

(another dwelling above)

Windows

Fully double glazed

Main heating

Electric storage heaters

Heating controls

Manual charge control

Hot water

Electric immersion, off-peak

Floor

(another dwelling below)

Energy improvement potential

Recommended improvements for this property

Measures from this home’s official Energy Performance Certificate assessment that could raise its rating and cut running costs, specific to 32, KENNERLEY COURT, KENNERLEY ROAD, DAVENPORT, STOCKPORT, SK2 6HL.

1. 1
   Change heating to gas condensing boilerIndicative cost: £3,000 - £7,000

   Changing the heating to use a mains gas boiler that provides both space and water heating will save money, as mains gas is currently cheaper than the fuel being used at present. A condensing boiler is capable of much higher efficiencies than other types of boiler, meaning it will burn less fuel to heat the property, but there may be exceptional circumstances making this impractical. Condensing boilers need a drain for the condensate which limits their location; remember this when considering remodelling the room containing the existing boiler even if the latter is to be retained for the time being (for example a kitchen makeover). This improvement is most appropriate when the existing heating system needs repair or replacement. It is best to obtain advice from a qualified heating engineer. Ask the engineer to explain the options. It is also recommended to change the electricity tariff to standard tariff when off-peak is no longer used.

2. 2
   Cavity wall insulationIndicative cost: £500 - £1,500

   Cavity wall insulation, to fill the gap between the inner and outer layers of external walls with an insulating material, reduces heat loss; this will improve levels of comfort, reduce energy use and lower fuel bills. The insulation material is pumped into the gap through small holes that are drilled into the outer walls, and the holes are made good afterwards. As specialist machinery is used to fill the cavity, a professional installation company should carry out this work, and they should carry out a thorough survey before commencing work to ensure that this type of insulation is suitable for this home. They should also provide a guarantee for the work and handle any building control issues. Further information about cavity wall insulation and details of local installers can be obtained from the National Insulation Association (www.nationalinsulationassociation.org.uk).

3. 3
   Increase hot water cylinder insulationIndicative cost: £15 - £30

   Increasing the thickness of existing insulation around the hot water cylinder will help to maintain the water at the required temperature; this will reduce the amount of energy used and lower fuel bills. An additional cylinder jacket or other suitable insulation layer can be used. The insulation should be fitted over any thermostat clamped to the cylinder. Hot water pipes from the hot water cylinder should also be insulated, using pre-formed pipe insulation of up to 50 mm thickness (or to suit the space available) for as far as they can be accessed to reduce losses in summer. All these materials can be purchased from DIY stores and installed by a competent DIY enthusiast.

4. 4
   Draught proof single-glazed windowsIndicative cost: £80 - £120

   Fitting draught proofing, strips of insulation around windows and doors, will improve the comfort in the home. A contractor can be employed but draught proofing can be installed by a competent DIY enthusiast.

5. 5
   Replacement glazing unitsIndicative cost: £1,000 - £1,400

   Replacing existing double-glazed units with new high-performance units will improve comfort in the home and reduce energy use.

Source: the property’s domestic EPC recommendations (open data). Indicative only, get a professional survey before committing to any measure.

Energy rating history

Recorded change: -3 EPC points across 2 certificates.

1. 2014C74
2. 2017C71

Other homes nearby