133 ESKDALE, TANHOUSE

Your options for this home

From the available property and energy data, this 80m² 1950s end-terrace home has a current EPC rating of E41 and mains-gas heating. HotAndCold estimates a space-heating requirement of approximately 5.0–7.0kW. This property's recorded energy efficiency is comparatively low. The estimated heat demand per square metre is around typical levels.

Hot&Cold snapshot

What stands out about this home

How this home compares locally

Based on 34 EPC-recorded properties nearby.

Sale history

Recorded sales for 133 ESKDALE from HM Land Registry Price Paid data.

1. £37,000

   Dec 2002 · Terraced

Contains HM Land Registry data © Crown copyright and database right. Sale prices are historic and not a current valuation.

Built form

End-terrace

Internal area (EPC)

80 m²

Building footprint

~50 m²

Approx. dimensions

~8.1 × 6.2 m

Main building axis

N–S

Nearest building

0.0 m

Footprint & dimensions derived from Overture Maps building data (ODbL). Approximate, not survey-grade.

How this home is constructed & heated

Recorded on its Energy Performance Certificate.

Walls

Cavity wall, filled cavity

Roof

Pitched, 200 mm loft insulation

Windows

Single glazed

Main heating

Boiler and radiators, mains gas

Heating controls

Programmer, room thermostat and TRVs

Hot water

From main system, no cylinder thermostat

Floor

Solid, no insulation (assumed)

Energy improvement potential

Recommended improvements for this property

Measures from this home’s official Energy Performance Certificate assessment that could raise its rating and cut running costs, specific to 133 ESKDALE, TANHOUSE, SKELMERSDALE, WN8 6ED.

1. 1
   Hot water cylinder thermostatIndicative cost: £200 - £400

   A hot water cylinder thermostat enables the boiler to switch off when the water in the cylinder reaches the required temperature; this minimises the amount of energy that is used and lowers fuel bills. The thermostat is a temperature sensor that sends a signal to the boiler when the required temperature is reached. To be fully effective it needs to be sited in the correct position and hard wired in place, so it should be installed by a competent plumber or heating engineer.

2. 2
   Replace single glazed windows with low-E double glazingIndicative cost: £3,300 - £6,500

   Double glazing is the term given to a system where two panes of glass are made up into a sealed unit. Replacing existing single-glazed windows with double glazing will improve comfort in the home by reducing draughts and cold spots near windows. Double-glazed windows may also reduce noise, improve security and combat problems with condensation.

3. 3
   Solar photovoltaic panels, 2.5 kWpIndicative cost: £9,000 - £14,000

   A solar PV system is one which converts light directly into electricity via panels placed on the roof with no waste and no emissions. This electricity is used throughout the home in the same way as the electricity purchased from an energy supplier. The British Photovoltaic Association has up-to-date information on local installers who are qualified electricians. It is best to obtain advice from a qualified electrician. Ask the electrician to explain the options.

4. 4
   Solar water heatingIndicative cost: £4,000 - £6,000

   A solar water heating panel, usually fixed to the roof, uses the sun to pre-heat the hot water supply. This will significantly reduce the demand on the heating system to provide hot water and hence save fuel and money. The Solar Trade Association has up-to-date information on local installers.

5. 5
   Floor insulationIndicative cost: £800 - £1,200

   Insulation of a floor will significantly reduce heat loss; this will improve levels of comfort, reduce energy use and lower fuel bills. Suspended floors can sometimes be insulated from below which means that the floor does not need to be lifted to install the insulation. Further information about floor insulation and details of local contractors can be obtained from the National Insulation Association (www.nationalinsulationassociation.org.uk).

6. 6
   Draught proof single-glazed windowsIndicative cost: £80 - £120

   Fitting draught proofing, strips of insulation around windows and doors, will improve the comfort in the home. A contractor can be employed but draught proofing can be installed by a competent DIY enthusiast.

7. 7
   Insulate hot water cylinder with 80 mm jacketIndicative cost: £15 - £30

   Installing an 80 mm thick cylinder jacket around the hot water cylinder will help to maintain the water at the required temperature; this will reduce the amount of energy used and lower fuel bills. A cylinder jacket is a layer of insulation that is fitted around the hot water cylinder. The jacket should be fitted over any thermostat clamped to the cylinder. Hot water pipes from the hot water cylinder should also be insulated, using pre-formed pipe insulation of up to 50 mm thickness (or to suit the space available) for as far as they can be accessed to reduce losses in summer. All these materials can be purchased from DIY stores and installed by a competent DIY enthusiast.

8. 8
   Low energy lighting for all fixed outletsIndicative cost: £60

   Replacement of traditional light bulbs with energy saving recommended ones will reduce lighting costs over the lifetime of the bulb, and they last up to 12 times longer than ordinary light bulbs. Also consider selecting low energy light fittings when redecorating; contact the Lighting Association for your nearest stockist of Domestic Energy Efficient Lighting Scheme fittings.

Source: the property’s domestic EPC recommendations (open data). Indicative only, get a professional survey before committing to any measure.

Other homes nearby