1 GLAISTER LANE, BOLTON

Your options for this home

Based on this property's recorded characteristics, this 69m² 1930s semi-detached home has a current EPC rating of E54 and its recorded heating. HotAndCold estimates a space-heating requirement of approximately 5.0–6.5kW. The recorded EPC score sits towards the lower end of the efficiency range. Its modelled space-heating intensity per square metre is moderate.

Hot&Cold snapshot

What stands out about this home

How this home compares locally

Based on 20 EPC-recorded properties nearby.

Built form

Semi-detached

Internal area (EPC)

69 m²

Building footprint

~51 m²

Approx. dimensions

~9.7 × 5.3 m

Main building axis

NW–SE

Nearest building

0.0 m

Footprint & dimensions derived from Overture Maps building data (ODbL). Approximate, not survey-grade.

How this home is constructed & heated

Recorded on its Energy Performance Certificate.

Walls

Cavity wall, filled cavity

Roof

Pitched, 150 mm loft insulation

Windows

Fully double glazed

Main heating

Electric storage heaters

Heating controls

Manual charge control

Hot water

Electric immersion, off-peak

Floor

Solid, no insulation (assumed)

Energy improvement potential

Recommended improvements for this property

Measures from this home’s official Energy Performance Certificate assessment that could raise its rating and cut running costs, specific to 1 GLAISTER LANE, BOLTON, BL2 5BU.

1. 1
   Solar photovoltaic panels, 2.5 kWpIndicative cost: £9,000 - £14,000

   A solar PV system is one which converts light directly into electricity via panels placed on the roof with no waste and no emissions. This electricity is used throughout the home in the same way as the electricity purchased from an energy supplier. The British Photovoltaic Association has up-to-date information on local installers who are qualified electricians. It is best to obtain advice from a qualified electrician. Ask the electrician to explain the options.

2. 2
   Floor insulationIndicative cost: £800 - £1,200

   Insulation of a floor will significantly reduce heat loss; this will improve levels of comfort, reduce energy use and lower fuel bills. Suspended floors can sometimes be insulated from below which means that the floor does not need to be lifted to install the insulation. Further information about floor insulation and details of local contractors can be obtained from the National Insulation Association (www.nationalinsulationassociation.org.uk).

3. 3
   Fan assisted storage heaters and dual immersion cylinderIndicative cost: £1,200 - £1,600

   Modern storage heaters are smaller and easier to control than the older type in the property. Ask for a quotation for new, fan-assisted heaters with automatic charge control. A dual-immersion cylinder, which can be installed at the same time, will provide cheaper hot water than the system currently installed. As installations should be in accordance with the current regulations covering electrical wiring, only a qualified electrician should carry out the installation. It is best to obtain advice from a qualified heating engineer. Ask the engineer to explain the options, which might also include switching to other forms of electric heating.

4. 4
   Wind turbineIndicative cost: £1,500 - £4,000

   A wind turbine provides electricity from wind energy. This electricity is used throughout the home in the same way as the electricity purchased from an energy supplier. The British Wind Energy Association has up-to-date information on suppliers of small-scale wind systems. Wind turbines are not suitable for all properties. The system’s effectiveness depends on local wind speeds and the presence of nearby obstructions, and a site survey should be undertaken by an accredited installer.

5. 5
   Solar water heatingIndicative cost: £4,000 - £6,000

   A solar water heating panel, usually fixed to the roof, uses the sun to pre-heat the hot water supply. This will significantly reduce the demand on the heating system to provide hot water and hence save fuel and money. The Solar Trade Association has up-to-date information on local installers.

6. 6
   Add additional 80 mm jacket to hot water cylinderIndicative cost: £15 - £30

   Increasing the thickness of existing insulation by adding an 80 mm cylinder jacket around the hot water cylinder will help maintain the water at the required temperature; this will reduce the amount of energy used and lower fuel bills. The jacket should be fitted over the top of the existing foam insulation and over any thermostat clamped to the cylinder. Hot water pipes from the hot water cylinder should also be insulated, using pre-formed pipe insulation of up to 50 mm thickness (or to suit the space available) for as far as they can be accessed to reduce losses in summer. All these materials can be purchased from DIY stores and installed by a competent DIY enthusiast.

Source: the property’s domestic EPC recommendations (open data). Indicative only, get a professional survey before committing to any measure.

Other homes nearby