FLAT 19, CLOUGH MILL

Your options for this home

Using the recorded floor area and EPC characteristics, this 70m² pre-1900 flat has a current EPC rating of E48 and its recorded heating. HotAndCold estimates a space-heating requirement of approximately 7.0–9.0kW. This property's recorded energy efficiency is comparatively low. The estimated heat demand per square metre is towards the higher end.

Hot&Cold snapshot

What stands out about this home

How this home compares locally

Based on 20 EPC-recorded properties nearby.

Built form

Flat

Internal area (EPC)

70 m²

Building footprint

~788 m²

Approx. dimensions

~56.9 × 17.9 m

Main building axis

E–W

Estimated floors

3

Nearest building

4.5 m

Footprint & dimensions derived from Overture Maps building data (ODbL). Approximate, not survey-grade.

How this home is constructed & heated

Recorded on its Energy Performance Certificate.

Walls

Sandstone or limestone, as built, no insulation (assumed)

Roof

(another dwelling above)

Windows

Fully double glazed

Main heating

Electric storage heaters

Heating controls

Manual charge control

Hot water

Electric immersion, off-peak

Floor

(another dwelling below)

Energy improvement potential

Recommended improvements for this property

Measures from this home’s official Energy Performance Certificate assessment that could raise its rating and cut running costs, specific to FLAT 19, CLOUGH MILL, SLACK LANE, LITTLE HAYFIELD, HIGH PEAK, SK22 2NJ.

1. 1
   Flat roof or sloping ceiling insulationIndicative cost: £1,500

   Insulation of a flat roof or sloping ceiling will significantly reduce heat loss through the roof; this will improve levels of comfort, reduce energy use and lower fuel bills. Where the weatherproof membrane is sound and the roof construction is appropriate, suitable insulation can be placed on top of the roof membrane (inverted roof). Alternatively, where the weatherproof membrane needs to be replaced insulation can be provided under the weatherproof membrane (warm roof). Further information about roof insulation and details of local contractors can be obtained from the National Insulation Association (www.nationalinsulationassociation.org.uk).

2. 2
   Low energy lighting for all fixed outletsIndicative cost: £25

   Replacement of traditional light bulbs with energy saving recommended ones will reduce lighting costs over the lifetime of the bulb, and they last up to 12 times longer than ordinary light bulbs. Also consider selecting low energy light fittings when redecorating; contact the Lighting Association for your nearest stockist of Domestic Energy Efficient Lighting Scheme fittings.

3. 3
   High heat retention storage heatersIndicative cost: £1,800

   Modern storage heaters have better insulation and are easier to control than the older type in the property. Ask for a quotation for new, high heat retention heaters with automatic charge and output controls. As installations should be in accordance with the current regulations covering electrical wiring, only a qualified electrician should carry out the installation. It is best to obtain advice from a qualified heating engineer. Ask the engineer to explain the options which might also include switching to other forms of electric heating.

4. 4
   50 mm internal or external wall insulationIndicative cost: £14,000

   Solid wall insulation involves adding a layer of insulation to either the inside or the outside surface of the external walls, which reduces heat loss and lowers fuel bills. As it is more expensive than cavity wall insulation it is only recommended for walls without a cavity, or where for technical reasons a cavity cannot be filled. Internal insulation, known as dry-lining, is where a layer of insulation is fixed to the inside surface of external walls; this type of insulation is best applied when rooms require redecorating and can be installed by a competent DIY enthusiast. External solid wall insulation is the application of an insulant and a weather-protective finish to the outside of the wall. This may improve the look of the home, particularly where existing brickwork or rendering is poor, and will provide long-lasting weather protection. Further information can be obtained from the National Insulation Association (www.nationalinsulationassociation.org.uk).

5. 5
   Heat recovery system for mixer showersIndicative cost: £725

   A shower heat recovery system extracts heat from the water in the shower drain and transfers it to incoming cold water. This reduces the amount of energy needed per shower.

6. 6
   Add additional 80 mm jacket to hot water cylinderIndicative cost: £30

   Increasing the thickness of existing insulation by adding an 80 mm cylinder jacket around the hot water cylinder will help maintain the water at the required temperature; this will reduce the amount of energy used and lower fuel bills. The jacket should be fitted over the top of the existing foam insulation and over any thermostat clamped to the cylinder. Hot water pipes from the hot water cylinder should also be insulated, using pre-formed pipe insulation of up to 50 mm thickness (or to suit the space available) for as far as they can be accessed to reduce losses in summer. All these materials can be purchased from DIY stores and installed by a competent DIY enthusiast.

Source: the property’s domestic EPC recommendations (open data). Indicative only — get a professional survey before committing to any measure.

Other homes nearby