91 SAPLING ROAD, BOLTON

Your options for this home

Based on this property's recorded characteristics, this 80m² 1930s mid-terrace home has a current EPC rating of E47 and its recorded heating. HotAndCold estimates a space-heating requirement of approximately 5.0–6.5kW. This property's recorded energy efficiency is comparatively low. The estimated heat demand per square metre is towards the lower end.

Hot&Cold snapshot

What stands out about this home

How this home compares locally

Based on 23 EPC-recorded properties nearby.

Built form

Mid-terrace

Internal area (EPC)

80 m²

Building footprint

~41 m²

Approx. dimensions

~8.8 × 4.6 m

Main building axis

NW–SE

Nearest building

0.0 m

Footprint & dimensions derived from Overture Maps building data (ODbL). Approximate, not survey-grade.

How this home is constructed & heated

Recorded on its Energy Performance Certificate.

Walls

Cavity wall, filled cavity

Roof

Pitched, 300 mm loft insulation

Windows

High performance glazing

Main heating

Room heaters, electric

Heating controls

Programmer and appliance thermostats

Hot water

Electric immersion, standard tariff

Floor

Solid, no insulation (assumed)

Energy improvement potential

Recommended improvements for this property

Measures from this home’s official Energy Performance Certificate assessment that could raise its rating and cut running costs, specific to 91 SAPLING ROAD, BOLTON, BL3 3QQ.

1. 1
   Floor insulation (suspended floor)Indicative cost: £5,000 - £10,000

   Insulation of a floor will significantly reduce heat loss; this will improve levels of comfort, reduce energy use and lower fuel bills. Suspended floors can often be insulated from below. . Further information about floor insulation is available from many sources including www.energysavingtrust.org.uk/northernireland/Insulation/Floor-insulation.

2. 2
   High heat retention storage heaters and dual immersion cylinderIndicative cost: £1,600 - £3,200

   Modern storage heaters are less expensive to run than the direct acting, on-peak heating system in the property. A dual-rate electricity supply is required to provide the off-peak electricity that these heaters use; this is easily obtained by contacting the energy supplier. Ask for a quotation for high heat retention heaters with automatic charge and output controls. A dual-immersion cylinder, which can be installed at the same time, will provide cheaper hot water than the system currently installed. As installations should be in accordance with the national wiring standards, only a qualified electrician should carry out the installation. Ask a qualified electrical heating engineer to explain the options, which might also include switching to other forms of electric heating.

3. 3
   Add additional 80 mm jacket to hot water cylinderIndicative cost: £20 - £40

   Increasing the thickness of existing insulation by adding an 80 mm cylinder jacket around the hot water cylinder will help maintain the water at the required temperature; this will reduce the amount of energy used and lower fuel bills. The jacket should be fitted over the top of the existing foam insulation and over any thermostat clamped to the cylinder. Hot water pipes from the hot water cylinder should also be insulated, using pre-formed pipe insulation of up to 50 mm thickness (or to suit the space available) for as far as they can be accessed to reduce losses in summer. All these materials can be purchased from DIY stores and installed by a competent DIY enthusiast.

4. 4
   Solar photovoltaic panels, 2.5 kWpIndicative cost: £8,000 - £10,000

   A solar PV system is one which converts light directly into electricity via panels placed on the roof with no waste and no emissions. This electricity is used throughout the home in the same way as the electricity purchased from an energy supplier. The British Photovoltaic Association has up-to-date information on local installers who are qualified electricians. It is best to obtain advice from a qualified electrician. Ask the electrician to explain the options.

5. 5
   Flat roof or sloping ceiling insulationIndicative cost: £900 - £1,200

   Insulation of a flat roof or sloping ceiling will significantly reduce heat loss through the roof; this will improve levels of comfort, reduce energy use and lower fuel bills. Where the weatherproof membrane is sound and the roof construction is appropriate, suitable insulation can be placed on top of the roof membrane (inverted roof). Alternatively, where the weatherproof membrane needs to be replaced insulation can be provided under the weatherproof membrane (warm roof). Further information about roof insulation and details of local contractors can be obtained from the National Insulation Association (www.nationalinsulationassociation.org.uk).

Source: the property’s domestic EPC recommendations (open data). Indicative only — get a professional survey before committing to any measure.

Other homes nearby