81 TRIMINGHAM DRIVE, BURY

Your options for this home

From the available property and energy data, this 144m² 1970s detached home has a current EPC rating of D56 and mains-gas heating. HotAndCold estimates a space-heating requirement of approximately 9.0–12.0kW. This property has moderate recorded energy efficiency, neither especially poor nor especially high. Its modelled space-heating intensity per square metre is relatively low.

Hot&Cold snapshot

What stands out about this home

How this home compares locally

Based on 10 EPC-recorded properties nearby.

Sale history

Recorded sales for 81 TRIMINGHAM DRIVE from HM Land Registry Price Paid data.

1. £250,000

   Jan 2016 · Detached

Contains HM Land Registry data © Crown copyright and database right. Sale prices are historic and not a current valuation.

Built form

Detached

Internal area (EPC)

144 m²

Building footprint

~85 m²

Approx. dimensions

~9.5 × 9.0 m

Main building axis

N–S

Estimated floors

2

Nearest building

1.7 m

Footprint & dimensions derived from Overture Maps building data (ODbL). Approximate, not survey-grade.

How this home is constructed & heated

Recorded on its Energy Performance Certificate.

Walls

Cavity wall, filled cavity

Roof

Pitched, 25 mm loft insulation

Windows

Fully double glazed

Main heating

Boiler and radiators, mains gas

Heating controls

Programmer, room thermostat and TRVs

Hot water

From main system, no cylinder thermostat

Floor

Suspended, no insulation (assumed)

Energy improvement potential

Recommended improvements for this property

Measures from this home’s official Energy Performance Certificate assessment that could raise its rating and cut running costs, specific to 81 TRIMINGHAM DRIVE, BURY, BL8 1EL.

1. 1
   Floor insulation (suspended floor)Indicative cost: £800 - £1,200

   Insulation of a floor will significantly reduce heat loss; this will improve levels of comfort, reduce energy use and lower fuel bills. Suspended floors can often be insulated from below. . Further information about floor insulation is available from many sources including www.energysavingtrust.org.uk/northernireland/Insulation/Floor-insulation.

2. 2
   Replace boiler with new condensing boilerIndicative cost: £2,200 - £3,000

   A condensing boiler is capable of much higher efficiencies than other types of boiler, meaning it will burn less fuel to heat this property. This improvement is most appropriate when the existing central heating boiler needs repair or replacement, but there may be exceptional circumstances making this impractical. Condensing boilers need a drain for the condensate which limits their location; remember this when considering remodelling the room containing the existing boiler even if the latter is to be retained for the time being (for example a kitchen makeover). It is best to obtain advice from a qualified heating engineer. Ask the engineer to explain the options.

3. 3
   Low energy lighting for all fixed outletsIndicative cost: £45

   Replacement of traditional light bulbs with energy saving recommended ones will reduce lighting costs over the lifetime of the bulb, and they last up to 12 times longer than ordinary light bulbs. Also consider selecting low energy light fittings when redecorating; contact the Lighting Association for your nearest stockist of Domestic Energy Efficient Lighting Scheme fittings.

4. 4
   Solar photovoltaic panels, 2.5 kWpIndicative cost: £5,000 - £8,000

   A solar PV system is one which converts light directly into electricity via panels placed on the roof with no waste and no emissions. This electricity is used throughout the home in the same way as the electricity purchased from an energy supplier. The British Photovoltaic Association has up-to-date information on local installers who are qualified electricians. It is best to obtain advice from a qualified electrician. Ask the electrician to explain the options.

5. 5
   Solar water heatingIndicative cost: £4,000 - £6,000

   A solar water heating panel, usually fixed to the roof, uses the sun to pre-heat the hot water supply. This will significantly reduce the demand on the heating system to provide hot water and hence save fuel and money. The Solar Trade Association has up-to-date information on local installers.

6. 6
   Hot water cylinder thermostatIndicative cost: £200 - £400

   A hot water cylinder thermostat enables the boiler to switch off when the water in the cylinder reaches the required temperature; this minimises the amount of energy that is used and lowers fuel bills. The thermostat is a temperature sensor that sends a signal to the boiler when the required temperature is reached. To be fully effective it needs to be sited in the correct position and hard wired in place, so it should be installed by a competent plumber or heating engineer.

7. 7
   Increase hot water cylinder insulationIndicative cost: £15 - £30

   Increasing the thickness of existing insulation around the hot water cylinder will help to maintain the water at the required temperature; this will reduce the amount of energy used and lower fuel bills. An additional cylinder jacket or other suitable insulation layer can be used. The insulation should be fitted over any thermostat clamped to the cylinder. Hot water pipes from the hot water cylinder should also be insulated, using pre-formed pipe insulation of up to 50 mm thickness (or to suit the space available) for as far as they can be accessed to reduce losses in summer. All these materials can be purchased from DIY stores and installed by a competent DIY enthusiast.

8. 8
   Increase loft insulation to 270 mmIndicative cost: £100 - £350

   Loft insulation laid in the loft space or between roof rafters to a depth of at least 270 mm will significantly reduce heat loss through the roof; this will improve levels of comfort, reduce energy use and lower fuel bills. Insulation should not be placed below any cold water storage tank; any such tank should also be insulated on its sides and top, and there should be boarding on battens over the insulation to provide safe access between the loft hatch and the cold water tank. The insulation can be installed by professional contractors but also by a capable DIY enthusiast. Loose granules may be used instead of insulation quilt; this form of loft insulation can be blown into place and can be useful where access is difficult. The loft space must have adequate ventilation to prevent dampness; seek advice about this if unsure (particularly if installing insulation between rafters because a vapour control layer and ventilation above the insulation are required). Further information about loft insulation and details of local contractors can be obtained from the National Insulation Association (www.nationalinsulationassociation.org.uk).

Source: the property’s domestic EPC recommendations (open data). Indicative only, get a professional survey before committing to any measure.

Other homes nearby