3, CHESTNUT MEWS

Your options for this home

Using the recorded floor area and EPC characteristics, this 60m² 1990s flat has a current EPC rating of C69 and its recorded heating. HotAndCold estimates a space-heating requirement of approximately 2.5–3.5kW. The recorded EPC score is comparatively high for existing housing stock. The estimated heat demand per square metre is towards the lower end.

Hot&Cold snapshot

What stands out about this home

How this home compares locally

Based on 125717 EPC-recorded properties nearby.

Built form

Flat

Internal area (EPC)

60 m²

Building footprint

~220 m²

Approx. dimensions

~22.2 × 9.9 m

Main building axis

NW–SE

Estimated floors

2

Nearest building

6.8 m

Footprint & dimensions derived from Overture Maps building data (ODbL). Approximate, not survey-grade.

How this home is constructed & heated

Recorded on its Energy Performance Certificate.

Walls

Cavity wall, as built, insulated (assumed)

Roof

Pitched, 300 mm loft insulation

Windows

Fully double glazed

Main heating

Electric storage heaters

Heating controls

Manual charge control

Hot water

Electric immersion, off-peak

Floor

(another dwelling below)

Energy improvement potential

Recommended improvements for this property

Measures from this home’s official Energy Performance Certificate assessment that could raise its rating and cut running costs, specific to 3, CHESTNUT MEWS, FAULKNERS LANE, GREAT WARFORD, KNUTSFORD, WA16 7RF.

1. 1
   Low energy lighting for all fixed outletsIndicative cost: £50

   Replacement of traditional light bulbs with energy saving recommended ones will reduce lighting costs over the lifetime of the bulb, and they last up to 12 times longer than ordinary light bulbs. Also consider selecting low energy light fittings when redecorating; contact the Lighting Association for your nearest stockist of Domestic Energy Efficient Lighting Scheme fittings.

2. 2
   Add additional 80 mm jacket to hot water cylinderIndicative cost: £30

   Increasing the thickness of existing insulation by adding an 80 mm cylinder jacket around the hot water cylinder will help maintain the water at the required temperature; this will reduce the amount of energy used and lower fuel bills. The jacket should be fitted over the top of the existing foam insulation and over any thermostat clamped to the cylinder. Hot water pipes from the hot water cylinder should also be insulated, using pre-formed pipe insulation of up to 50 mm thickness (or to suit the space available) for as far as they can be accessed to reduce losses in summer. All these materials can be purchased from DIY stores and installed by a competent DIY enthusiast.

3. 3
   High heat retention storage heatersIndicative cost: £1,800

   Modern storage heaters have better insulation and are easier to control than the older type in the property. Ask for a quotation for new, high heat retention heaters with automatic charge and output controls. As installations should be in accordance with the current regulations covering electrical wiring, only a qualified electrician should carry out the installation. It is best to obtain advice from a qualified heating engineer. Ask the engineer to explain the options which might also include switching to other forms of electric heating.

4. 4
   Party wall insulationIndicative cost: £600

   Party wall insulation, to fill the gap in the wall separating two or more dwellings walls with an insulating material, reduces heat loss; this will improve levels of comfort, reduce energy use and lower fuel bills. The insulation material is pumped into the gap through small holes that are drilled into the party wall, and the holes are made good afterwards. As specialist machinery is used to fill the cavity, a professional installation company should carry out this work, and they should carry out a thorough survey before commencing work to ensure that this type of insulation is suitable for this home. They should also provide a guarantee for the work and handle any building control issues. Further information about cavity wall insulation and details of local installers can be obtained from the National Insulation Association (www.nationalinsulationassociation.org.uk).

Source: the property’s domestic EPC recommendations (open data). Indicative only — get a professional survey before committing to any measure.

Other homes nearby